3rd Edition

Design Analysis in Rock Mechanics

By William G. Pariseau Copyright 2017
    730 Pages
    by CRC Press

    730 Pages
    by CRC Press

    This comprehensive introduction to rock mechanics treats the basics of rock mechanics in a clear and straightforward manner and discusses important design problems in terms of the mechanics of materials. This extended third edition includes an additional chapter on Foundations on Jointed Rock.

    Developed for a complete class in rock engineering, this volume uniquely combines the design of surface and underground rock excavations and addresses:
    • rock slope stability in surface excavations, from planar block and wedge slides to rotational and toppling failures
    • shaft and tunnel stability, ranging from naturally-supported openings to analysis and design of artificial support and reinforcement systems
    • entries and pillars in stratified ground
    • three-dimensional caverns, with emphasis on cable bolting and backfill
    • geometry and forces of chimney caving, combination support and trough subsidence
    • rock bursts and bumps in underground excavations, with focus on dynamic phenomena and on fast and sometimes catastrophic failures.

    The numerous exercises and examples familiarize the reader with solving basic practical problems in rock mechanics through various design analysis techniques and their applications. Supporting the main text, appendices provide supplementary information about rock, joint, and composite properties, rock mass classification schemes, useful formulas, and an extensive literature list. The large selection of problems at the end of each chapter can be used for home assignment. A solutions manual is available to course instructors.

    Explanatory and illustrative in character, this volume is suited for courses in rock mechanics, rock engineering and geological engineering design for undergraduate and first year graduate students in mining, civil engineering and applied earth sciences. Moreover, it will form a good introduction to the subject of rock mechanics for earth scientists and engineers from other disciplines.

    1 Introduction
    1.1 A practical design objective
    1.2 Problem solving
    1.3 Units
    1.4 Background information
    1.5 Problems

    2 Slope stability
    2.1 Translational rock slope failures
    2.2 Rotational slope failures
    2.3 Problems

    3 Shafts
    3.1 Single unlined naturally supported shafts
    3.2 Shaft wall support and liners
    3.3 Multiple naturally supported shafts
    3.4 Problems

    4 Tunnels
    4.1 Naturally supported tunnels
    4.2 Tunnel support
    4.3 Problems

    5 Entries in stratified ground
    5.1 Review of beam analysis
    5.2 Softrock entries
    5.3 Problems

    6 Pillars in stratified ground
    6.1 Pillars in a single seam
    6.2 Pillars in dipping strata
    6.3 Pillars with joints
    6.4 Pillars in several seams
    6.5 Barrier pillars
    6.6 Problems

    7 Three-dimensional excavations
    7.1 Naturally supported caverns and stopes
    7.2 Joints in cavern and stope walls
    7.3 Tabular excavations
    7.4 Cavern and stope support
    7.5 Problems

    8 Subsidence
    8.1 Chimneys
    8.2 Troughs
    8.3 Problems

    9 Dynamic phenomena
    9.1 Fundamentals of wave propagation
    9.2 Rock bursts and bumps
    9.3 Event location
    9.4 Problems

    10 Foundations on jointed rock
    10.1 Plane plastic strain
    10.2 Uniformly loaded strip
    10.3 Bearing capacity near the surface
    10.4 Problems

    Appendix A: Background literature
    A.1 Books about fundamentals of mechanics
    A.2 Books about rock mechanics
    A.3 Books containing rock properties
    A.4 General sources of rock mechanics information

    Appendix B: Mechanical properties of intact rock and joints
    B.1 Elastic moduli of intact rock
    B.2 Strength of intact rock
    B.3 Joint stiffness
    B.4 Joint strength
    B.5 Simple combinations of intact rock and joints

    Appendix C: Rock mass classification schemes for engineering
    C.1 Rock quality designation
    C.2 Terzaghi modified scheme
    C.3 RSR, RMR, and Q
    C.4 Comparisons of Hp estimates
    C.5 GSI
    C.6 Comment

    Appendix D: Some useful formulas
    D.1 Stress
    D.2 Strain
    D.3 Stress–strain relationships, Hooke’s law


    William Pariseau obtained his B.S. degree in Mining Engineering at the University of Washington (Seattle) following the geological option and subsequently earned a Ph.D. in Mining Engineering at the University of Minnesota with emphasis on rock mechanics and with a minor in applied mathematics. Prior to his Ph.D., he obtained practical experience working for the City of Anchorage, the Alaska Department of Highways, the Mineral Resources Division of the U.S. Bureau of Mines (Spokane), the Anaconda Copper Co. in Butte, Montana, the New York-Alaska Gold Dredging Corp. in Nyac, Alaska. He served in the United States Marine Corps (1953-1956). He maintained a strong association with the former U.S. Bureau of Mines, first with the Pittsburgh Mining Research Center and later with the Spokane Mining Research Center. He is a registered professional engineer and has consulted for a number of commercial and government entities.
    Currently, he is a professor emeritus and former holder of the Malcolm McKinnon endowed chair in mining engineering at the University of Utah. He joined the Department in 1971 following academic appointments at the Montana College of Science and Technology and the Pennsylvania State University. He has been a visiting academic at Brown University, Imperial College, London, and at the Commonwealth Science and Industrial Research Organization (CSIRO), Australia. He and colleagues have received a number of rock mechanics awards; he was recognized as a distinguished university research professor at the University of Utah in 1991. In 2010, he was recognized for teaching in the College of Mines and Earth Sciences with the Outstanding Faculty Teaching Award. The same year, he was honored by the Old Timers Club with their prestigious Educator Award. He was honored as a Fellow of the American Rock Mechanics Association in 2015.

    "The 3rd edition of the text book Design Analysis in Rock Mechanics by William G. Pariseau completes the author’s goal, stated in his first edition, of including a chapter on foundation engineering that follows the addition of a chapter on dynamic phenomena given in his second edition.

    As an instructor, I use this textbook as the foundation for the entire class. It is not an easy textbook to complete. It is dense but clearly written so that one may understand the physics, and hence the solution approach, behind the many types of encountered rock mechanic problems. By carefully reading the text, a set of notes can be developed by the instructor in giving lectures to their students. The lectures will assist the student in understanding the assigned reading and associated problems presented in each chapter. An excellent solution manual is also available. The first chapter begins by emphasizing the time-tested engineering approach toward problem solving and shows in a step-by-step manner the application of scientific laws, diagramming, and mathematical calculations in the solution process. This solution process is repeated as new material is presented in the following chapters of; slope stability, shafts, tunnels, entries and pillars in stratified ground, three-dimensional excavations, subsidence, dynamic phenomena, and foundations on jointed rock. By the end of the course the students will gain a great deal of knowledge and develop their critical thinking and problem solving skills to help form them into practicing engineers."

    Jeffrey C. Johnson, Associate Professor at the Department of Mining Engineering, University of Utah, USA.